Orantek IP226 Скачать руководство пользователя страница 13

Страница: 13 / 54

Camera

Camera Setup

Camera

Light frequency -

Two options: 50Hz & 60Hz. set according to the mains frequency in the country. For UK this would

be 50Hz.

For the USA this would be 60 KHz.

Image mirror -

Show mirrored view of the video.

Image flip vertical -

Image can be flipped up and down.

Moonlight mode -

Turn

On/OFF

the brightness setting according to the light intensity of the area being monitored

manually.

Auto -

automatic enhance ambient brightness when it is necessary.

Power LED light -

Turn on/off the power & network LED indicator of camera.

Microphone

Volume -

Adjusts the volume of the microphone from 0~14 where 0 is the lowest.

G.726 bit rate -

Four options: 16, 24, 32, 40(kbps). Determines the quality of the audio being transmitted. The most

commonly used mode is 32 Kbit/s.

Audio bit rate -

Four options: 16, 24, 32, 40(kbps). Determines the quality of the audio being transmitted.

AMR bit rate -

Eight options will Determines the quality of the audio being transmitted.

Default audio codec -

to choice default codec, when alarm triggers event to record on SD card or somewhere else.

Noise Reduction

- enable this feature to filter out ambient noise.

Speaker Out

- Enables or disables the Audio Upload. (This feature only for outdoor camera)

Note

: If the camera is inversely installed, images flip horizontally and images flip vertically should be turned on at the

same time.

Содержание IP226























































Результаты поиска

Содержание IP226

Отзывы:

Бренды по названию

Популярные бренды

Orantek IP226, Руководство пользователя

Результаты поиска

Содержание IP226

Отзывы:

Бренды по названию

Популярные бренды