Oracle X7-8 Скачать руководство пользователя страница 50

Страница: 50 / 308

Identify Hardware Faults (Oracle ILOM)

■

“Identify Hardware Faults (Oracle ILOM)” on page 50

■

“Using Oracle ILOM” in

Oracle Server X7-8 Installation Guide

Identify Hardware Faults (Oracle ILOM)

Use this procedure to troubleshoot hardware faults with the Oracle ILOM web interface and, if

necessary, prepare the server for service.

Note -

The screens and information in this procedure might differ from those for your server.

This example procedure provides one method to troubleshoot hardware faults using Oracle

ILOM web and CLI interfaces. However, the procedure can be performed using only the Oracle

ILOM CLI interface. For more information about Oracle ILOM interfaces, refer to the Oracle

ILOM documentation.

Obtain the latest version of the

Oracle Server X7-8 Product Notes Release 1.0

Log in to the server SP Oracle ILOM web interface.

Open a browser and type in the IP address of the server SP. Enter a user name (with

administrator privileges) and password at the log-in screen. The Summary Information page

appears.

View the

Status

section of the summary Information page to identify the server

subsystem that requires service.

The Status section of the Summary screen provides information about the server subsystems,

such as:

■

“Processor Subsystem” on page 82

■

“Memory Subsystem” on page 83

■

“Power Subsystem” on page 83

■

“Cooling Subsystem” on page 84

■

“Storage Subsystem” on page 86

■

“Networking Subsystem” on page 87

■

“PCI Devices Subsystem” on page 88

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды