manualshive.com logo in svg

Oracle X7-8, Руководство по обслуживанию

Поделиться
Скачать
Oracle X7-8 Скачать руководство пользователя страница 84

Troubleshooting Server Subsystems

processor (SP). When power is supplied to the SP, the SP boots, and the server enters the low-

power Standby power mode.

Once the SP boots into Standby power, Main power is initiated by pressing and releasing the

chassis front panel On/Standby button or by powering on the server remotely from Oracle

ILOM.

Each PSU is rated for 3060W continuous output. Input is 220V VAC only (50-60Hz). Main

output is 12V @244A. Standby output is 12V at 5A. The MAX input line current (200-277

VAC input) is less than 16 Amps RMS. The minimum holdup is 12ms for Main output and

40ms for Standby.

For more information about power control, see 

“Power Control, Shutdown, and Reset

States” on page 118

.

Cooling Subsystem

Use the Oracle Integrated Lights Out Manager (ILOM) Cooling page to view the health and

number of fans installed in your system. Additionally, you can view the server inlet and exhaust

temperatures. Review the Fans table for details about the health and location of individual fans.

System cooling air flows from front to back. Primary cooling is provided by eight redundant

front panel accessible 100 watt hot-swappable cooling fan modules.

To maintain the integrity of the chassis cooling system, ensure that:

■

Empty slots have filler panels. All necessary fillers ship with the system.

■

Each drive bay contains a storage device or a drive slot filler.

■

All DPCCs are installed regardless of whether they contain a card or not.

■

Both fan frames are populated with fan modules.

■

Each fan frame and fan module is populated.

■

All CMOD processors have a heat sink.

■

Each SMOD bay has an SMOD or filler.

Cooling Zones

The server has five front-to -back cooling zones. The cooling zones are numbered from left

to right (from the front of the server) as zone 0 - zone 4. The airflow cooling in zone 0 is

84

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды