Oracle X7-8 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 308

Oracle X7-8 Скачать руководство пользователя страница 82

Troubleshooting Server Subsystems

■

“Cooling Subsystem” on page 84

■

“Storage Subsystem” on page 86

■

“Networking Subsystem” on page 87

■

“PCI Devices Subsystem” on page 88

For component serviceability, locations, and designations, see

Components” on page 24

.

Processor Subsystem

Use the Oracle Integrated Lights Out Manager (ILOM) Processors page to view the health of

the CPUs installed on the CMODs.

The server processor subsystem consists of the following:
On-demand configuration for one 4-socket server, two independent 4-socket servers, or one 8-

socket server.

■

Processors: Up to eight Intel Xeon vx processors.

■

Intel 8168 processor, 24-core, 2.7-GHz, 205W (4-socket servers or 8-socket server)

■

Intel 8160 processor, 24-core, 2,1-GHz, 150W (4-socket servers or 8-socket server)

■

Intel 6140 processor, 18-core, 2.3-GHz, 150W (4-socket servers)

■

Intel 6128 processor, 6-core, 3.4-GHz, 125W (4-socket servers)

Four CMOD configuration:

■

Must be in 4-socket mode.

■

Must have CMODs in slots 0 -3 (slots 4-7 for side B)

■

DPCC slots 0-3 active (4-7 for side B)

■

Both fan frames must be installed.

■

All 8 fan modules must be installed. Fan modules FM0-3 will be active (FM4-7 for System

B)

■

Processors with the following capabilities are supported:

■

Intel 8168 processor, 24-core, 2.7-GHz, 205W (4-socket servers or 8-socket server)

■

Intel 8160 processor, 24-core, 2,1-GHz, 150W (4-socket servers or 8-socket server)

■

Intel 6140 processor, 18-core, 2.3-GHz, 150W (4-socket servers)

■

Intel 6128 processor, 6-core, 3.4-GHz, 125W (4-socket servers)

Eight CMOD configuration:

82

Oracle Server X7-8 Service Manual • October 2017

«
...
80
81
82
83
84
...
»

Содержание X7-8





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды