Oracle X7-2 Скачать руководство пользователя страница 30

Страница: 30 / 148

X7-2L Front Panel Features

Call Out

Description

Network (NET) 10/100/1000BASE-T RJ-45 Gigabit Ethernet (GbE) port: NET 0

Network (NET) 10GBASE-T RJ-45 GbE port: NET 1

Network (NET) 10GBASE-T RJ-45 GbE port: NET 2

Network (NET) 10/25GbE SFP+ port: NET 1

Network (NET) 10/25GbE SFP+ port: NET 2

USB 3.0 connector

Serial management (SER MGT) RJ-45 serial port

Note -

The 10/25 GbE SFP+ Ethernet ports (NET1 and NET2) are the default network ports.

Related Information

■

“X7-2 Front Panel Features” on page 27

■

“Server Components” on page 25

X7-2L Front Panel Features

The following figure shows the status indicators (LEDs), connectors, and drives located on the

front panel of a Oracle Server X7-2L configured with twelve 3.5-inch storage drives.

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Содержание X7-2





















































































































































Результаты поиска

Содержание X7-2

Отзывы:

Похожие инструкции для X7-2

Бренды по названию

Популярные бренды

Oracle X7-2, Руководство по установке

Результаты поиска

Содержание X7-2

Отзывы:

Похожие инструкции для X7-2

Бренды по названию

Популярные бренды