Oracle Sun Netra X4270 Скачать руководство пользователя страница 43

Страница: 43 / 238

BIOS Setup Utility Menus

Interface

NET0

NET1

NET2

NET3

VMware ESX 4.0 and

ESXi 4.0

vmnic#

†

vmnic#

†

For VMware, the Ethernet port that the user assigns to the service console will be vmnic0. Other ports are mapped by ascending order

of the PCI bus enumerations.

Related Information

■

“Rear Panel Cable Connections” on page 17

■

“Ethernet Port LEDs” on page 24

■

“Ethernet Port Booting Priority” on page 43

■

“Gigabit Ethernet Ports” on page 215

Ethernet Port Booting Priority

The order in which the BIOS detects the Ethernet ports during boot time, and the corresponding

drivers that control those ports, are listed below:
1. NET 0 (INTEL NIC 0)
2. NET 1 (INTEL NIC 1)
3. NET 2 (INTEL NIC 2)
4. NET 3 (INTEL NIC 3)

Related Information

■

“Ethernet Port LEDs” on page 24

■

“Ethernet Port Device and Driver Naming” on page 42

■

“Gigabit Ethernet Ports” on page 215

BIOS Setup Utility Menus

The following table provides descriptions for the seven top-level BIOS setup utility menus.

TABLE 6

BIOS Setup Menus Summary

Menu

Description

Main

General product information, including BIOS type, processor, memory, and time/date.

Using the BIOS Setup Utility

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды