Oracle Sun Netra X4270 Скачать руководство пользователя страница 42

Страница: 42 / 238

Understanding BIOS Booting and Setup

2. After exiting out of DRAM, the BIOS performs a simple memory test (where a write/read

of every location with the pattern 55aa55aa is performed).

Note -

The simple memory test is performed only if Quick Boot is not enabled from the

Boot Settings Configuration screen. Enabling Quick Boot causes the BIOS to skip the

memory test.

3. The BIOS polls the memory controllers for both correctable and non-correctable memory

errors and logs those errors into the SP.

4. The message, BMC Responding, displays at the end of POST.

Related Information

■

“Default BIOS POST Events” on page 38

■

“BIOS POST F1 and F2 Errors” on page 39

Ethernet Port Device and Driver Naming

The server supports four 10/100/1000BASE-T Gigabit Ethernet ports on the rear of the chassis.

The device naming for the Ethernet interfaces is reported differently by different interfaces and

operating systems. See the table below for the logical (operating system) and physical (BIOS)

naming conventions used for each interface.

TABLE 5

Logical Port Naming

Interface

NET0

NET1

NET2

NET3

BIOS

slot 108

slot 109

slot 110

slot 111

Solaris 10 10/09

igb0

igb1

igb2

igb3

OpenSolaris 2010.3

igb0

igb1

igb2

igb3

RHEL5.4 (64-bit)

eth0

eth1

eth2

eth3

Oracle Enterprise

Linux (OEL) 5.4 (64-

bit)

eth0

eth1

eth2

eth3

SLES 10 SP3 (64-bit)

and

SLES 11 (64-bit)

eth0

eth1

eth2

eth3

Windows 2008

net1

net2

net3

net4

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды