Oracle Sun Netra X4270 Скачать руководство пользователя страница 215

Страница: 215 / 238

Identifying the Server Ports

These topics describe the pinouts of the server connectors.

■

“Gigabit Ethernet Ports” on page 215

■

“Network Management Port” on page 216

■

“Serial Management Port” on page 217

■

“Video Connector” on page 219

■

“Alarm Port” on page 220

■

“USB Ports” on page 221

■

“External SAS Connector” on page 222

■

“PCI Mezzanine Auxiliary Power Connector” on page 223

Related Information

■

“Understanding the Server” on page 13

Gigabit Ethernet Ports

The server has four autonegotiating 10/100/1000BASE-T Gigabit Ethernet system domain

ports. All four Ethernet ports use a standard RJ-45 connector. The transfer rates are shown in

the following table.

Connection Type

IEEE Terminology

Transfer Rate

Ethernet

10BASE-T

10 Mbps

Fast Ethernet

100BASE-TX

100 Mbps

Gigabit Ethernet

1000BASE-T

1000 Mbps

The following figure and table describe the gigabit Ethernet port pin signals.

Identifying the Server Ports

215

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды