Oracle Sun Netra X4270 Скачать руководство пользователя страница 18

Страница: 18 / 238

Locating Server and Component LEDs

Note -

To comply with NEBS lightning requirements, all I/O connections (except the Ethernet

and power connections) must be made using shielded cables, and both ends of the shield must

be grounded.

Note -

All of the PCIe slots comply with the PCI Express 2.0 specification and can

accommodate 25 W PCIe2 cards.

Related Information

■

“Rear Panel LED Locations” on page 23

■

“Power Supply LEDs” on page 23

■

“Disconnect Cables From the Server” on page 80

■

“Reconnect Power and Data Cables” on page 213

■

“Identifying the Server Ports” on page 215

Locating Server and Component LEDs

These topics describe the LEDs located on the front and rear of the server, including those

found on components and ports.

■

“System Status LEDs” on page 19

■

“User Alarm LEDs” on page 20

■

“Drive LEDs” on page 21

■

“Rear Panel LED Locations” on page 23

■

“Power Supply LEDs” on page 23

■

“Ethernet Port LEDs” on page 24

Related Information

■

“Locating Controls and Connectors” on page 13

■

“Service Troubleshooting Task List” on page 30

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды