Oracle SPARC T8-2 Скачать руководство пользователя

Страница: 125 / 188

Install a PCIe Card or Filler

Rotate the crossbar to an upright position (panel 1).

Carefully remove the PCIe card or filler from the card slot (panel 2).

Replace with another PCIe card or filler before the server is connected to power

again.

See

“Install a PCIe Card or Filler” on page 125

Related Information

■

“Install a PCIe Card or Filler” on page 125

Install a PCIe Card or Filler

Caution -

This procedure requires that you handle components that are sensitive to ESD which

can cause server components to fail.

Note -

Always update optional PCIe card firmware to the latest supported version. Refer to the

PCIe card documentation for firmware update instructions.

Take the necessary ESD precautions.

See

“Prevent ESD Damage” on page 55

Ensure that the server is powered off and all power cords are disconnected from

the server power supplies.

See

“Removing Power From the Server” on page 51

Determine which slot to install the PCIe card in.

If you are not replacing an existing PCIe card and need information about deciding which slot

to install the card in, see

“PCIe Card Configuration” on page 119

Disengage the PCIe card slot crossbar from its locked position by pulling it

toward the interior of the chassis.

The crossbar might already be disengaged if you removed a PCIe card or filler from that slot.

Install the PCIe card or filler into the card slot and return the crossbar to its

closed and locked position.

Servicing PCIe Cards

125

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды