Oracle SPARC Enterprise M3000 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 552

background image

deleteboard(8)

System Administration

41

EXTENDED

DESCRIPTION

■

You can execute the

deleteboard

(8) command under the environment where

the following services, managed by the Solaris Service Management Facility
(SMF), are in operation:

■

Domain SP Communication Protocol (dscp service) is working properly and
the network with XSCF has been established

■

Domain Configuration Server (dcs service) is working properly

■

Sun cryptographic key management daemon (sckmd service) is working
properly

■

When the command is executed, a prompt to confirm execution of the command
with the specified options is displayed. Enter "

y

" to execute the command or "

n

"

to cancel the command.

■

If "

-c disconnect"

is specified when either the domain power has been turned

off or the XSB is already disconnected from the domain configuration, no
operation is performed. If domain power-on or power-off is in progress, the
command results in an error.

■

If

"-c unassign"

is specified when either the domain power has been turned

off or the XSB is already disconnected from the domain configuration, the XSB is
switched from the assigned state to a system board pool. If the XSB is already in
a system board pool, no operation is performed.

■

If

"-c reserve"

is specified when either the domain power has been turned off

or the XSB is already disconnected from the domain configuration, the XSB is
immediately switched from the assigned state to a system board pool. If the XSB
is already in a system board pool, no operation is performed. If domain power-
on or power-off is in progress, the command results in an error.

■

When the XSB is disconnected, the hardware resource on the XSB is disconnected
from the operating system. For this reason, command execution may take time.

■

The state in which an XSB has been assigned means that configuring the XSB in
the specified domain has been reserved. The reserved XSB is configured when
the domain is rebooted or the

addboard

(8) command is executed. An already

assigned XSB cannot be specified for configuring or assignment from other
domains.

■

An XSB in the system board pool means that the XSB belongs to no domain and
is therefore available for configuring or assignment.

EXAMPLES

EXAMPLE 1

Puts the system board XSB#00-0, #01-0, #02-0, and #03-0 in the system board
pool

EXAMPLE 2

Reserves disconnection of XSB#00-0, #01-0, #02-0, and #03-0 .

XSCF>

deleteboard -c unassign 00-0 01-0 02-0 03-0

XSCF>

deleteboard -c reserve 00-0 01-0 02-0 03-0

«
...
51
52
53
54
55
...
»

Содержание SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPARC Enterprise M3000

ColorPASS-Z5000

Бренд: Canon Страницы: 134

HS21 XM BLADECENTER - L5408 FOR SPEC CPU2006

Бренд: IBM Страницы: 1

UniServer R4300 G5

Бренд: H3C Страницы: 16

Enterprise Server 33

Бренд: Blackberry Страницы: 207

FusionServer G8600 V7

Бренд: xFusion Digital Technologies Страницы: 112

SuperServer 6029U-TR25M

Бренд: Supermicro Страницы: 151

Бренд: QNAP Страницы: 16

6180DN - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренд: Inventec Страницы: 129

Бренд: EVS Страницы: 118

SpectraLink 020

Бренд: Polycom Страницы: 47

QS-RETAILBOX PRO

Бренд: Visel Italiana Страницы: 12

Бренд: Axis Страницы: 172

Бренд: Supero Страницы: 104

SecureBox SDS2100

Бренд: Lantronix Страницы: 70

Бренд: Lantronix Страницы: 370

Бренд: SVT Страницы: 16

Yingxin NF5280M2

Бренд: Inspur Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды