Oracle SPARC Enterprise M3000 Скачать руководство пользователя страница 281

Страница: 281 / 552

setroute(8)

System Administration

267

NAME

setroute - set routing information for an XSCF network interface

SYNOPSIS

setroute

-c

{

add

del

}

-n

address

[

-m

address

] [

-g

address

]

interface

setroute

-h

DESCRIPTION

setroute

(8) command sets routing information for an XSCF network interface.

Up to eight routing information items can be registered for each network interface.
Any attempt to register more than eight items causes an error.

Privileges

You must have

platadm

privilege to run this command.

Refer to

setprivileges

(8) for more information.

OPTIONS

The following options are supported:

-c

{

add

del

}

Specifies a function for routing information. One of the following
values can be specified. If none of them is specified, an error
occurs.

add

Adds routing information.

del

Deletes routing information.

-g

address

Specifies a gateway address used for routing. To specify

address

use the standard form of four integer values delimited by "

(periods). For example, use

xxx

, where

xxx

is an

integer from 0-255. Zero suppression can be used to specify the
integer.

You cannot specify the loopback address (127.0.0.0/8), the
network address, or a broadcast address.

Содержание SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SPARC Enterprise M3000

Отзывы:

Похожие инструкции для SPARC Enterprise M3000

Бренды по названию

Популярные бренды

Oracle SPARC Enterprise M3000, Справочное руководство

Результаты поиска

Содержание SPARC Enterprise M3000

Отзывы:

Похожие инструкции для SPARC Enterprise M3000

Бренды по названию

Популярные бренды