Oracle SPARC Enterprise M3000 Скачать руководство пользователя страница 529 | Manualshive

Страница: 529 / 552

background image

testsb(8)

System Administration

507

■

XSB is installed in the domain and this domain is in OpenBoot PROM (

ok>

prompt) status.

■

XSB is installed in the domain and this domain is power ON status, power
OFF status, or reboot status.

■

The

addboard

(8),

deleteboard

(8), or

moveboard

(8) command is executed

for XSB.

■

In case an XSB which belongs to the specified PSB is in

Unmount

or

Faulted

status, it may be excluded from the target of diagnosis and may not be shown in
the diagnosis result. In a case like this, use the

showboards

(8) command to

check the diagnosis result.

■

In case there are the settings for the warm-up time of the system and the wait
time before system startup, a prompt appears to confirm whether or not it can
ignore these settings to execute the

testsb

(8) command. Enter "

y

" to execute the

command or "

n

" to cancel the command.

■

The displayed diagnostic results of the

testsb

(8) command are as follows:

XSB

XSB numbers belonging to the specified PSBs. One XSB number
is displayed for the Uni-XSB type, and four XSB numbers are
displayed for the Quad-XSB type.

Test

Status of the initial diagnosis of XSBs. One of the following status
values is displayed:

Unmount

No XSB could be recognized because no XSB
is mounted or because an error occurred.

Unknown

Not tested.

Testing

Initial diagnosis is in progress.

Passed

Initial diagnosis ended normally.

Failed

An error was detected during the initial
diagnosis. An XSB cannot be used or is in a
degraded state.

Fault

XSB error. One or more states are displayed:

Normal

Normal state.

Degraded

One or more components are degraded. Each
XSB can operate.

Faulted

An XSB cannot operate because an error
occurred.

«
...
527
528
529
530
531
...
»

Содержание SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPARC Enterprise M3000

Бренд: Panasonic Страницы: 28

Бренд: Z Microsystems Страницы: 17

Бренд: HYVE Страницы: 22

Бренд: Sun Microsystems Страницы: 128

D-811_002-NXS-SAG

Бренд: NOMACHINE Страницы: 19

Бренд: Velvac Страницы: 55

FP-SER-ETH-SERVR2

Бренд: RCI Страницы: 17

Бренд: SystemBase Страницы: 118

Бренд: pachanko Страницы: 56

Бренд: Planet Страницы: 2

Бренд: Mirapoint Страницы: 76

Бренд: 360 Systems Страницы: 148

Бренд: Ampair Страницы: 26

Бренд: TROY Group Страницы: 35

Бренд: SMC Networks Страницы: 19

Бренд: Gigabyte Страницы: 147

Бренд: Dell EMC Страницы: 108

Бренд: Dell EMC Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды