OptiPure 164-01502 Скачать руководство пользователя страница 12

OPS70CR Simple Install Guide 

12 

Open

Closed

v

 

Operation

The system operates normally when water, 

under pressure, is supplied to the system. Typical 

filter replacement is every 6 months (CTOS-Q10, 

CTOS-Q10CR, and ILMA-10.14). Typical 

membrane replacement is every 24 months 

(AMS-QT10) or less, based on water quality. 

EMERGENCY BYPASS

In the event the water supply or pressure to 

downstream equipment becomes inadequate 

OPEN the Built-In Bypass Valve and resume 

normal use of equipment. When finished using 

equipment return the Valve to the CLOSED 

position. DO NOT leave the system in bypass 

mode for prolonged periods of time. 

IMPORTANT: Leaving the system in bypass 

could cause damage to downstream 

equipment. If the problem persists contact 

your OptiPure dealer for assistance. 

Step 1

Close Feed Water Supply Valve.

OR

Be sure Bypass Valve is closed and turn 

pre-filter cartridge 1/4 turn to the left .

Step 2

Close the Storage Tank Valve.

Tank Valve  in 
CLOSED position

v

 

SHUT OFF WATER TO SYSTEM

The water is now shut off 

and the system is 

ready for filter or membrane replacement or 

other maintenance.

To return to normal operation reverse these 

steps.

Содержание 164-01502













Отзывы: