Optex SC-U1 Скачать руководство пользователя страница 89

Страница: 89 / 92

Maintenance

Perform the following items every month.

• Inspect the installation bracket for corrosion.
• Inspect the cover and operation panel for dirt.

Use a clean and soft cloth for cleaning. Remove dirt with diluted mild detergent, and use a
dry cloth to wipe dry.

Do not use organic solvent for cleaning.

Otherwise deformation or malfunction may occur.

Check the following items every 3 months.

•  SC-U1 is tightly fixed.
•  SC-U1 is not out of order without any damage.
•  Terminal block screws are not rusted.

If the SC-U1 is not used over a prolonged period, keep it as follows:

1. Turn OFF the power switch and disconnect the power cable.
2. Store the SC-U1 away from direct sunlight.

Maintenance (Monthly)

Periodic Inspection (Every 3 Months)

Long-Term Storage

Содержание SC-U1





























































































Результаты поиска

Содержание SC-U1

Отзывы:

Похожие инструкции для SC-U1

Бренды по названию

Популярные бренды

Optex SC-U1, Руководство по эксплуатации

Результаты поиска

Содержание SC-U1

Отзывы:

Похожие инструкции для SC-U1

Бренды по названию

Популярные бренды