Grow Wall 3
A. Assembly
A1. Remove all the parts from box and check all the accessories
Thank you for purchasing OPCOM Farm Grow Wall 3 , the indoor hydroponics growing system. lt is designed for easy to use and
efficient growth by one-touch AUTO mode.lt holds up to 144 plants capacity. Please read the quick guide carefully before setting it up.
For detailed user guide video, please visit Grow Wall 3 page at http://www.opcomfarm.com
A2. Assemble GrowWall 3
Hang the four planting groove on the four screws of different
heights on the column, and fasten with a pull buckle to fix it.
Assemble the left and right three short column into two left
and right column.
1
2
Assemble two wall brackets in a rotating manner behind the
top beam and tear off the double-sided tape and stick to the
wall.
4
Place the top beam on the top of the column and fix it with
a buckle.
3
Rotate the downspout up and down and disassemble it into
an upper downspout and a lower downspout.
After nest the upper downspout with metal gaskets and
waterproof gaskets through the drain hole at the bottom of
the planting groove, rotate the lower downspout from the
bottom of the planting groove to the upper downspout tightly.
5
Hang the L-shaped hard pipe of the upper water pipe on the
right side of the uppermost planting groove, pass the hose
below the L-shaped hard pipe through the pipe groove of the
right column, nest the end of the hose over the port on the
right side of the water tank above the pump pack.
6
Lock the four LED grow lights to the four light arms using the screws you removed from two sides of the LED grow lights.
8
Put four filter sponges on the upper downspout in the four
planting groove, one filter sponge on the filter in the water
tank, and cover the four planting trays on the four planting
groove respectively.
7
Connect the 6 round hole plugs plugged into the main line of the control box to the fan (Fan), the motor (Pump) and the 4 LED growth
lights respectively, and insert the power supply plug of the control box into the socket. Insert the cable tie terminal corresponding to the
main line into the corresponding hole of the right column.
9
Water Control Box:
1. Open the water control box on the left side of the water tank by pulling up the side planks. Take out the water drain pipe form the
storing disk.
2.Prepare a water bucket with a capacity of around 40 L. Place the outlet of thepipe un the bucket. Press the Pump button to turn on
the pump and switch the water drain valve to 'Out' to start draining.
3.Once finished draining, press the Pump button to turn off the pump and switch the water drain valve to 'Stop' to stop draining.
Set everything back to default.
A3. LED light planting mode Control
1. Select the mode of the LED grow light (you may switch between modes through the button on the left side of the LED lamp
holder)(see figure 1), the light comes with two modes: G and L.
2. Height of the LED grow light: Adjust the height and the angle of lighting manually through the rocker arm(see figure 2).
3. This hydroponics system comes with fans that improve the air circulation and accelerate the cooling of the LED tubes, which
increases the ventilation and avoids plants from overheating. Please make sure to keep a 5-10 cm distance between the light
tube and the plants to further prevent plants from overheating. To boost the light intensity in a power-saving way, direct the
light at both the plant and the wall simultaneously, which could add 30% more lighting to the plants.
Chart I: Control Box
Restore factory settings after power failure.
Status
Fuction
ON
OFF
ON
OFF
Operation
One Press
Wifi pairing
Long press 5 sec
One Press
One Press
One Press
LED
ON
OFF
One Press
One Press
Fan
Pump
Panel Light
Smart Control Box
11 gallons
（
40L
）
Water Drain pipe
Water Cycling Valve
Water Drain Valve
Water Cycling Valve
Please read and follow every steps to avoid any malfunction.
B. Seedling
Chart II: Plant Stage
1. Add water to the seedling tray, up to the water (red) level.(Fig1)
2. Open Grow Sponge package,put each sponge piece into water of seedling tray (make sure the
front side with the seed label is side up), press the sponges into water 5 seconds and ensure the
sponges absorb water completely. Put seed moisturizing cover on the sponges.(Fig2)
3. Place the seedling tray with cover in the shade.(Fig3)
4. Suggest using Watering Spray water to sponges and keep them wet
everyday.
5. During 0 ~ 7 days, find the sprouted ones in the tray; pick them out, and
move them into product and to next stage: B2. Young Plant Stage.
6. Discard unsprouted sponges after regular germination time.
7. In each sponge, keep strong plants and cut the other weak plants.
* Different plant may have different germination time, please check before plant.
B1. Germination Stage
B2.Young Plant Stage
1. Add 10.5 gallons water to the water tank.
2. During Young Plant Stage, turn on LED and Pump. Please refer to the ChartII.
3. Add Salt #1 (Nutrition) into the water tank and ensure EC value between(=1.0-2.0mS/cm)
EC value Status
Adjustment method
when 0.0-0.5
Add 2g Salt #1
when 0.5-1.0
Add 1g Salt #1
when 1.0-1.5
Standard range
when over 2.0
Add water
Basil, Lemon Balm
Germination Stage
Planting Time
Day 0~7
LED Mode
OFF
Pump Mode
OFF
Notes
* For your expected plant amount, you can refer to the sprout rate of 1st planting cycle.
* If you need more planting information, please vist to www.opcomfarm.com and read “Plant Q&A”.
Nutrition
Don’t need
T
( )
68 - 77
RH
80%
EC
0.5-1.0
PH
5.5-6.5
Young Plant Stage
Day 3~14
G Mode
ON
59 - 86
45%-70% 1.0-2.0
5.5-6.5
Growing Stage
After Day 14
L Mode
Free setting
59 - 86
45%-70% 1.0-2.0
5.5-6.5
Be sure each sponge is fully wet in
seedling tray.
* Please keep the seeds in refrigerator if you don’t use it, recommended temperture is 41
-
50.
Need
Need
Seedling Tray x2pcs
(665*175*65mm)
Grow Kits
Assembly
Grow Sponge 60pk
x9pcs (OASP001)
EC test
pen x1pc
Accessories
Top water
pipe x 1pc
Warranty
Card
Manual
Downpipes
x4pcs
Wall support
column x2pcs
Soda
(pH+)
50ml x1
Salt #1
(Nutrition)
250ml x2
Lemon
(pH-)
50ml x2
Cleaning
ponge x1pc
Water
Spray x1pc
Filter
Sponge x5pcs
Planting Tray
(36 holes) x4pcs
B Scoop for
Adjust of
Nutritio (5g)
planting basket
(25mm) x150pcs
PH test
paper x1pc
Alkaline
Neutral
Acidic
column x 6pcs
Top beam x1pc
planting groove x4pcs
Water tank x1pc
Fig1
Fig2
Fig3
Adjust the height of lighting
Adjust the angle of lighting
figure 2
figure 1
Operation
Status
Switch to G
Switch to OFF
Switch to L
LED grow
light planting
mode
L
G
OFF
Operation
Fuction
R1
column
R2
column
R3
column
L1 planting groove
Water tank
L2 planting groove
L3 planting groove
L4 planting groove
fan beam
Conrtol
Box
Fan power
LED3
power
LED2
power
LED1
power
Pump
power
LED4
power
LED Growth Light x4pcs
4
9
9
9
7
6
7
6
6
1
2
2
9
5
5
3
7
