OnRobot 3FG15 Скачать руководство пользователя страница 52

Страница: 52 / 177

Additional Software Options

3FG15

The state of the gripper could be:

•

Busy

- the gripper is in motion

•

Grip detected

- the gripper has detected a workpiece

•

Force grip detected

- the gripper has applied the target force to a workpiece. This also

activates a break. See more info in section

Finger movement and force on page 79.

The gripper can be controlled in two modes:

•

Move

mode - The easiest way to move the gripper but the gripping force is limited (<50N).

This should be used to release a part and open the gripper.

•

Grip

mode - This should be used to properly grip a part with a given target force. If the

part is properly gripped (target force is reached) the break will engage to make sure the

part will not be dropped in case of a power loss.

Содержание 3FG15


















































































































































































Результаты поиска

Содержание 3FG15

Отзывы:

Бренды по названию

Популярные бренды

OnRobot 3FG15, Руководство пользователя

Результаты поиска

Содержание 3FG15

Отзывы:

Бренды по названию

Популярные бренды