OnRobot 3FG15 Скачать руководство пользователя страница 22

Страница: 22 / 177

Installation

3.3

Wiring

Three cables need to be connected to wire the system properly:

•

Tool data cable between the tool(s) and the Compute Box

•

Ethernet communication cable between the robot controller and the Compute Box

•

Power supply of the Compute Box

NOTE:

For the Quick Changer - Robot Side no cable is needed to be connected.

3.3.1

Tool data cable

First connect the data cable to the tool.

For Single or Dual 3FG15, RG2, RG6, Screwdriver, SG, VG10 or VGC10

Use the M8-8pin connector on the Quick

Changer or on the Dual Quick Changer.
Use the cable holder as illustrated on the left.

CAUTION:

Make sure to use the supplied

cable holder to prevent any

excessive strain on the 90-

degree M8 connector caused by

the rotation of the cable.

For RG2-FT

For RG2-FT the Quick Changer tool data

connector cannot be used. Instead use the

marked M8-4pin connector

bending radius

extra length

Robot

controller

Содержание 3FG15


















































































































































































Результаты поиска

Содержание 3FG15

Отзывы:

Бренды по названию

Популярные бренды

OnRobot 3FG15, Руководство пользователя

Результаты поиска

Содержание 3FG15

Отзывы:

Бренды по названию

Популярные бренды