OnRobot 3FG15 Скачать руководство пользователя страница 176

Страница: 176 / 177

Certifications

176

VG10

CE/EU Declaration of Incorporation (Original)

According to European Machinery Directive 2006/42/EC annex II 1.B.

The manufacturer:

OnRobot A/S

Teglværskvej 47H

DK-5220, Odense SØ

DENMARK

declares that the product:

Type:

Industrial Robot Gripper

Model:

VG10

Generation: V2

Serial:

1000000000-1009999999

may not be put into service before the machinery in which it will be incorporated is declared in

conformity with the provisions of Directive 2006/42/EC, including amendments, and with the

regulations transposing it into national law.
The product is prepared for compliance with all essential requirements of Directive 2006/42/EC

under the correct incorporation conditions, see instructions and guidance in this manual.

Compliance with all essential requirements of Directive 2006/42/EC relies on the specific robot

installation and the final risk assessment.

Technical documentation is compiled according to Directive 2006/42/EC annex VII part B and

available in electronic form to national authorities upon legitimate request. Undersigned is

based on the manufacturer address and authorized to compile this documentation.

Additionally, the product declares in conformity with the following directives, according to

which the product is CE marked:

2014/30/EU

—

Electromagnetic Compatibility Directive (EMC)

2011/65/EU

—

Restriction of the use of certain hazardous substances (RoHS)

Relevant essential health and safety requirements of the following EU directives are also

applied:

2014/35/EU

—

Low Voltage Directive (LVD)

2012/19/EU

—

Waste of Electrical and Electronic Equipment (WEEE)

A list of applied harmonized standards, including associated specifications, is provided in this

manual.

Budapest, December 16th, 2019

Group Management

Vilmos Beskid

CTO

Содержание 3FG15


















































































































































































Результаты поиска

Содержание 3FG15

Отзывы:

Бренды по названию

Популярные бренды

OnRobot 3FG15, Руководство пользователя

Результаты поиска

Содержание 3FG15

Отзывы:

Бренды по названию

Популярные бренды