Onicon Vortex Flow Meter F-2200 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 22

Onicon Vortex Flow Meter F-2200 Series Скачать руководство пользователя страница 15

F-2200 Series Vortex Flow Meter Installation and Operation Guide • Revised 12/08

16

3.2.1.2 Rotating the display

To rotate the display, fi rst unscrew the cover using the special tool provided for this

purpose. Once the cover is removed, the (4) Philips head screws that secure the

display are exposed. To rotate the display, remove these screws and carefully move it

to the desired position making certain that the interconnecting cable is not damaged

in the process.

!

3.2.2 Flanged-Type Connection To Ansi B16.5 (Schedule 40)

Meter

sizes

3/8”, 1/2”, 3/4”, 1”, 1 1/2”, 2”, 3”, 4”, 6”, 8”

Pipe

fl anges

To ANSI: #300 standard,

#600 optional

Gaskets are supplied with fl anged units.

Center the fl ow meter by sight.

Check the fl ange connections for leak-tightness

after the fl ow meter installation.

CAUTION

•

Do not remove enclosure covers in any wet environment

•

Keep dirt and debris out of electronics enclosure

•

Keep threads lubricated (silicone based lubricant)

•

Do not over tighten covers. Use special tool for removal only.

«
...
13
14
15
16
17
...
»

Содержание Vortex Flow Meter F-2200 Series























Отзывы:

Нет отзывов