Onicon F-5000 Скачать руководство пользователя страница 25

Страница: 25 / 28

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 10/16 - 2032 / 107050

Page 25

Zero CAL-CHECK™ Performed on:

September 23 2016

10:30:29

Firmware version:

F-5500 V3.6

Serial Number:

N00003

Zero CAL-CHECK™ Results:

ZERO CAL-CHECK PASS

Zero CAL-CHECK™:

0.32

Test Temperature

73.1 F

Tag #/Meter Location:

Test performed by:

Additional Comments:

* Sensor free of residue or film
* Zero Stability of the meter
* Thermal Conductivity (heat transfer) repeatability of the sensor

Zero CAL-CHECK™ is a calibration routine that validates the flow meter's calibration accuracy by testing the following:

At the conclusion of the test, the meter will display a pass/fail message and the Zero CAL-CHECK™ data.

A "pass" result confirms the meter is measuring accurately.

CALIBRATION VALIDATION

Zero CAL-CHECK™ CERTIFICATE

Zero CAL-CHECK

Certificate

The Zero CAL-CHECK

Certificate function displays the latest certification. When

performing a Zero CAL-CHECK

test, all the data is logged into a log file with all

pertinent data, including the serial number. A laptop or PC can be used to perform the
Zero CAL-CHECK

test on the F-5000 meter. When a Zero CAL-CHECK

certificate

is requested, the program will search the log file for the specific serial number and will
display only the last check performed.

Fig. 3.19: Zero CAL-CHECK

Certificate

Zero CAL-CHECK

Log

The "View Log" button allows the operator to view a log of previous Zero CAL-CHECK

tests that have been executed on the meter.

Fig. 3.20: Zero CAL-CHECK

Log

F-5000 View

OPERA

TION

Operation: Zero CAL-CHECK

Certificate

Zero CAL-

CHECK

Certificate

Zero CAL-

CHECK

Log

Содержание F-5000





























Результаты поиска

Содержание F-5000

Отзывы:

Onicon F-5000, Инструкция по установке и эксплуатации, Страница: 25 / 28

Результаты поиска

Содержание F-5000

Отзывы: