Onicon F-5000 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 28

Onicon F-5000 Скачать руководство пользователя страница 12

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 10/16 - 2032 / 107050

Page 12

Save Setting

The user can save any new chart settings on the main page window. These settings

can then be closed by clicking on the "X" at the top right corner of the window.

Parameters

All meter operating parameters can easily be selected for charting: flow, temperature

or total flow.

Total Points

The total points specifies the number of points plotted on the graph. Older data is

automatically omitted.

Update Rate

The update rate controls the data refresh rate.

Percent (%) Scale

This sets the scale to a plus/minus specified percentage from the initial measured

value. Typically, the minimum/maximum is scaled at plus/minus 10% of that initial

value.

Manual Chart Setting

The Manual mode allows a user to input min/max values for chart scaling. When

entering new values, press enter for them to take effect.

Automatic Chart Setting

Automatic mode lets the program adjust the scaling on a real-time basis based on the

entire range of values.

Configure

F-5000 View

OPERA

TION

Operation: Chart Settings

Charts

Settings

«
...
10
11
12
13
14
...
»

Содержание F-5000





























Отзывы:

Нет отзывов