Omron Xpectia-FZ3 Series Скачать руководство пользователя страница 53

Страница: 53 / 58

SECTION 4

Support measurement functions

4-1

Image Logging

This is used when saving measurement images to on-board memory, RAM-
Disk or USB memory.

This enables preparation of logging conditions using an expression and is
more flexible than the system image logging conditions settings.

However, the settings of this unit are enabled if „None“ is set on the [Logging
setting] of the main screen [Measure] menu.

If settings that perform image logging for multiple units during measurement
are executed, the last settings executed are enabled.

• This is used when saving logging images under specific conditions.

4-1-1

Logging Conditions (Image Logging)

Setting item

Set value [Factory default]

Description

Logging condition

• [None]

No images are saved.

• Only NG

Saves images only if an NG
occurs.If an NG occurs down-
stream from the image logging
processing unit, image logging
is not performed.

Insert image logging as close to
the end of the scene as possible

• All

All measured images are saved.

Содержание Xpectia-FZ3 Series



























































Результаты поиска

Содержание Xpectia-FZ3 Series

Отзывы:

Похожие инструкции для Xpectia-FZ3 Series

Бренды по названию

Популярные бренды

Omron Xpectia-FZ3 Series, Быстрое руководство

Результаты поиска

Содержание Xpectia-FZ3 Series

Отзывы:

Похожие инструкции для Xpectia-FZ3 Series

Бренды по названию

Популярные бренды