background image

5-6 

Reader/Writer Control Commands

5-6

 

5-49 

5-6-1  Stop (ST) 

Stop (ST) Stop command terminates Auto mode, Repeat mode, EAS check and other command 

processings, as well as continued FIFO state after FIFO Access, or Select state after executing 

Detection command, returning to the Reader/Writer to a stand-by status to wait for commands.

 

 

<Command Format> 

STX 

 

Node No. 

 

Command 

code 

"ST" 

ETX BCC

1 2 

2 1 

<Response Format> 

STX Node 

No. 

 

Retry 

flag 

Command 

code 

"ST" 

Response 

code 

"00" 

ETX BCC

1 2 1 2 

2 1 

 

Response code 

00: Normal completion 

For other response codes, refer to 5-3-7Response Code List. 

 
 

5-6-2  Reset (XZ) 

Reset Command resets the Reader/Writer software. No response is returned for this command. 

Other commands are rejected during the software reset process (approximately 2.5 seconds). 

 

<Command Format> 

STX 

 

Node No. 

 

Command 

code 

"XZ" 

ETX BCC

1 2 

2 1 

 

5-6-3  ACK(AK)  

This command is used during ACK/NACK control to inform the Reader/Writer that the host device 
normally received a response from the Reader/Writer. There is no response if this command is used in 
ACK/NACK control, but if the Reader/Writer is not waiting to receive ACK/NACK signals, an error will 
occur when the command is received. Refer to SECTION 5-1-3 ACK/NACK Control for details. 

 <Command 

Format> 

STX 

 

Node No. 

 

Command 

code 

"AK" 

ETX BCC

1 2 

2 1 

 

5-6-4  NACK(NK)  

This command is used during ACK/NACK control to inform the Reader/Writer that the host device did not 
normally receive a response from the Reader/Writer. When the Reader/Writer receives a NACK command, 
the previous response is retried provided that the maximum number of retries (9) has not been exceeded. 

If the Reader/Writer is not waiting to receive ACK/NACK signals, an error will occur when the 

command is received. Refer to SECTION 5-1-3 ACK/NACK Control for details. 

 
<Command Format> 

STX 

 

Node No. 

 

Command 

code 

"NK" 

ETX  BCC

1 2 

2 1 

 

Содержание V720S-BC5D4A






















































































































































Отзывы: