Omron sysmac EtherNet/IP NJ Series Скачать руководство пользователя

Страница: 23 / 68

．

EtherNet/IP Connection Procedure

The Gateway Configuration

Window is displayed.

The search of the USB driver to

connect Personal computer and

netTAP automatically starts.

The search results are displayed

in the Device Assignment Pane

on the right side of the window.

*If no search results are found,

the USB driver for connection
to netTAP may not have been
correctly installed on Personal
computer. Install the USB
driver in the correct way, and
repeat from step 1 of this
procedure.

Select

netX Driver

found in the

search results (select the check

box) as a method for connecting

Personal computer and netTAP.

In the Navigation area, click

Configuration

–

Settings

The Settings Pane is displayed

on the right side of the window.

Set the following parameters in

the

Protocol Combinations

Field.

- Primary network (Port X2):

EtherNet/IP Adapter

- Secondary network (Port X3):

DeviceNet Master

Содержание sysmac EtherNet/IP NJ Series





































































Результаты поиска

Содержание sysmac EtherNet/IP NJ Series

Отзывы:

Похожие инструкции для sysmac EtherNet/IP NJ Series

Бренды по названию

Популярные бренды

Omron sysmac EtherNet/IP NJ Series, Руководство по подключению

Результаты поиска

Содержание sysmac EtherNet/IP NJ Series

Отзывы:

Похожие инструкции для sysmac EtherNet/IP NJ Series

Бренды по названию

Популярные бренды