![background image](http://html1.mh-extra.com/html/omron/stc-mbe132u3v/stc-mbe132u3v_product-specifications-and-users-manual_742901049.webp)
No.13S062-07
49/53
STC-MBE132U3V / MCE132U3V / STC-MCE132U3V-C
Product Specifications and User’s Guide
9.16.3
AcquisitionControl
Name
Description
AcquisitionMode
Sets the acquisition mode of the device. It defines mainly the number of frames to
capture during an acquisition and the way the acquisition stops.
AcquisitionStart
Starts the Acquisition of the device. The number of frames captured is specified by
AcquisitionMode.
AcquisitionStop
Stops the Acquisition of the device at the end of the current Frame. It is mainly used
when AcquisitionMode is Continuous but can be used in any acquisition mode.
AcquisitionArm
Arms the device before an AcquisitionStart command. This optional command validates
all the current features for consistency and prepares the device for a fast start of the
Acquisition.
AcquisitionFrameRate
Controls the acquisition rate (in Hertz) at which the frames are captured.
TriggerSelector
Selects the type of trigger to configure.
TriggerMode
Controls if the selected trigger is active.
TriggerSoftware
Generates an internal trigger. TriggerSource must be set to Software.
TriggerSource
Specifies the internal signal or physical input Line to use as the trigger source. The
selected trigger must have its TriggerMode set to On.
TriggerDelay
Specifies the delay in microseconds (us) to apply after the trigger reception before
activating it.
ExposureMode
Sets the operation mode of the Exposure (or shutter).
ExposureTimeSelector
Selects which exposure time is controlled by the ExposureTime feature. This allows for
independent control over the exposure components.
ExposureTime
Sets the Exposure time when ExposureMode is Timed and ExposureAuto is Off. This
controls the duration where the photosensitive cells are exposed to light.
ExposureTimeAbs
Sets the Exposure time when ExposureMode is Timed and ExposureAuto is Off. This
controls the duration where the photosensitive cells are exposed to light.
ExposureTimeRaw
Sets the Exposure time when ExposureMode is Timed and ExposureAuto is Off. This
controls the duration where the photosensitive cells are exposed to light.
ExposureAuto
Sets the automatic exposure mode when ExposureMode is Timed. The exact algorithm
used to implement this control is device-specific.
ExposureAutoLimitMax
Determine the upper limit of exposure time when ExposureAuto is set to Continuous.
ExposureAutoLimitMin
Determine the lower limit of exposure time when ExposureAuto is set to Continuous.
9.16.4
TransportLayerControl
Name
Description
PayloadSize
Provides the number of bytes transferred for each image or chunk on the stream
channel. This includes any end-of-line, end-of-frame statistics or other stamp data. This
is the total size of data payload for a data block.
9.16.5
DigitalIOControl
Name
Description
LineSelector
Selects the physical line (or pin) of the external device connector to configure.
LineMode
Controls if the physical Line is used to Input or Output a signal.
LineInverter
Controls the inversion of the signal of the selected input or output Line.
LineStatus
Returns the current status of the selected input or output Line.
LineSource
Selects which internal acquisition or I/O source signal to output on the selected Line.
LineMode must be Output.
UserOutputSelector
Selects which bit of the User Output register will be set by UserOutputValue.
UserOutputValue
Sets the value of the bit selected by UserOutputSelector.
StrobeOutDelay
Delay of StrobeOut signal when LineSource is set to StrobeOut(us).
StrobeOutOnTime
Duration of StrobeOut signal when LineSource is set to StrobeOut(us).
TriggerOutDelay
Delay of TriggerOut signal when LineSource is set to TriggerOut(us).
TriggerOutOnTime
Duration of TriggerOut signal when LineSource is set to TriggerOut(us).