background image

11   EtherCAT Coupler Unit Functions

11 - 12

NX-series EtherCAT Coupler Unit User’s Manual (W519)

11-5 Event Logs

The EtherCAT Slave Terminal supports the event logs of NJ-series Controllers. This allows you to use 
the NJ-series Controller to perform troubleshooting.

This section describes event logging for EtherCAT Slave Terminals.

Refer to the 

NJ-series Troubleshooting Manual

 (Cat. No. W503) for information on troubleshooting the 

entire NJ-series Controller.

The EtherCAT Slave Terminal records events, such as errors and status changes, that occur in the 
EtherCAT Slave Terminal. You can use the Sysmac Studio to check the meaning of the events in the 
EtherCAT Slave Terminals.

"Event" for an EtherCAT Slave Terminal is a generic term for an unexpected error or for information that 
does not indicate an error but for which the user must be notified.

11-5-1 Introduction

EtherCAT 
Coupler Unit

Sysmac Studio

Event logs

Event logs

NJ-series CPU Unit

Use the Sysmac Studio to check past and current events for the following:

• EtherCAT Slave Terminal

• NJ-series Controller

Sysmac Studio (when connected to the USB port 
on the EtherCAT Coupler Unit)

Use the Sysmac Studio to check past and current events for the following:

• EtherCAT Slave Terminal

Содержание NX-ECC201























































































































































































































































































































































































































Отзывы: