background image

K8DT-AS

5

Timing Charts

Overcurrent Operation Diagram 
(Output Drive Method: Normally Open)

DIP switch setting: SW3 OFF, SW4 OFF

Undercurrent Operation Diagram 
(Output Drive Method: Normally Closed)

DIP switch setting: SW3 ON, SW4 ON

Nomenclature

Front

Note:

Use solid wires, stranded wires, or ferrules to connect to the 
terminals.
To maintain the withstand voltage after connecting the 
terminals, insert 8 mm of exposed conductor into the terminal.

Indicators

Setting Knobs

Hysteresis
(5% to 50% of operating value)

Lit

Flashing

t

t: Operating time (0.1 to 30 s)

Delay time: 250 ms 
(reference value)

LOCK: Startup lock time (0 to 30 s) 

LOCK

Power supply 

voltage

Contacts 11-14 or 

transistor output

Contacts 11-12

Set value

Input

Alarm indicator

Hysteresis (5% to 50% of operating value)

Flashing

t

t: Operating time (0.1 to 30 s)

Power supply 

voltage

Contacts 11-12

Set value

Alarm indicator

Lit

Contacts 11-14 or 

transistor output

Input

Delay time: 250 ms (reference value)

Terminal block

 (See note.)

Terminal block

 (See note.)

Current knob (SV)

Hysteresis knob (HYS)

Operating time knob (T)

Startup lock time knob
(LOCK)

Power indicator

Output status indicator

Alarm indicator

8 mm

8 mm

Solid Wire

8 mm

Stranded Wires

Ferrules

Item

Meaning

Power indicator 
(PWR: Green)

Lit when power is being supplied.

Output status indicator 
(Output: Yellow)

Lights for output 

Alarm indicator 
(ALM: Red)

Lit when there is an overcurrent or 
undercurrent. 
The indicator flashes to indicate the error 
status after the input has exceeded the set 
value while the operating time is being 
clocked. 

Item

Usage

Current knob (SV)

Used to set the current to 10% to 100% of 
maximum setting range.

Hysteresis knob (HYS)

Used to set the rest value to 5% to 50% of 
the operating value.

Operating time knob (T)

Used to set the operating time to 0.1 to 30 s.

Startup lock time knob 
(LOCK)

Used to set the startup lock time to 0 to 30 s.

Содержание K8DT-AS Seriesl

















Отзывы: