F3S-A
j
j
j
j
P
F3S-A
j
j
j
j
P
4
Specifications
J
RATINGS AND PERFORMANCE
Part number
F3S-A161P F3S-A321P F3S-A481P F3S-A082P F3S-A162P F3S-A242P F3S-A322P F3S-A402P F3S-A482P
No. of beams
16
32
48
8
16
24
32
40
48
Protective height
150 mm
(5.91 in)
310 mm
(12.2 in)
470 mm
(18.5 in)
140 mm
(5.51 in)
300 mm
(11.81 in)
460 mm
(18.11 in)
620 mm
(24.41 in)
780 mm
(30.7 in)
940 mm
(37.01 in)
Beam spacing
10 mm (0.39 in)
20 mm (0.79 in)
Optical resolution
Non-transparent: 15 mm (0.59 in)
in diameter
Non-transparent: 25 mm (0.98 in) in diameter
Sensing range
0.2 to 5.0 m (7.87 in to 16.40 ft)
Response
i
ON
→
OFF 20 ms max.
p
time
OFF
→
ON 55 ms max. (with stable light)
Supply voltage
24 VDC
±
10% (ripple range (p-p): 10% max.)
Current consumption
200 mA max. (under no-load conditions)
Light source
Infrared LED (860-nm wavelength)
Angle of divergence
Within
±
2
°
for the emitter and receiver at a detection distance of at least 3 m as provided by prEN50100-2.
Operating mode
Light ON
Control output
Two PNP transistor outputs, 300 mA max. load current, and 2 V max. residual voltage (except for voltage drop
due to cord extension)
Multiplex circuitry
Using sync line connection (between an emitter and a receiver and between multiple Light Curtains)
No. of serial connections: Up to 3 sets
No. of parallel connections: Up to 4 sets
Total no. of beams: Up to 192 (with mixed serial and parallel connection)
External diagnosis
function
(See Note 1.)
After power ON
External diagnosis input line: Open or 9 to 24 V: Emitting OFF
External diagnosis input line: 0 to 1.5 V: Emitting ON (3 mA max. short-circuit current)
Interference light
search function (See
Note 1.)
Prior to power ON
External diagnosis input line: Open or 9 to 24 V: Interference light search
External diagnosis input line: 0 to 1.5 V: Emitting ON (3 mA max. short-circuit current)
Indicator
Emitter
Light indicator (orange LED): Lit when emitting, flashing during external diagnosis and interference light
search.
Fault indicator (yellow LED): Lit with emitter lock-out, flashing during emitter OFF-hold and interference light
search. (See Note 2.)
Receiver
ON-state indicator (green LED): Lit when receiving light.
OFF-state indicator (red LED): Lit with interrupted light or failure, flashing during interference light
search. (See Note 2.)
Instability indicator (orange LED): Lit with an insufficient light margin and interference light search.
Fault indicator (yellow LED): Lit with receiver lock-out, flashing during receiver OFF hold and interference light
search. (See Note 2.)
Connection method
Connector on 400 mm (15.75 in) cables; use extension cables
Protection circuit
Output short circuit protection
Ambient
Operation --10
°
to 55
°
C (14
°
F to 131
°
F) with no freezing
temp
Storage
--30
°
to 70
°
C (--22
°
F to 158
°
F) with no freezing
Ambient
h
idi
Operation 35 to 85% RH (with no condensation)
humidity
Storage
35 to 95% RH
(This table continues on the next page.)
Note: 1. The logic (ON/OFF) may differ from that normally used because a safety circuit is used. Be sure to check this carefully.
2. Lock-out: Output status OFF due to unrecoverable failure. OFF-hold: Output status OFF due to temporary failure.
3. In accordance with prEN50100-1
4. The optional extension cord provides the same cable specifications.
(Reference) Resistance: Power line and output line: 66.3
Ω
/Km
Sync line: 94.0
Ω
/Km
Use a cable of at least the same performance to extend the cable length. The total cable length must be 100 m or less.
Downloaded from
Downloaded from
Downloaded from
