background image

8

Limit Controller

 

E5CN-FR

Operating Method

Outline of Operation Procedures

The following diagram illustrates the entire setting level. A password is required to enter the advance function setting level and the calibration level.
Some parameters may not be displayed depending on the protection settings and operation conditions.
The control operation will stop when switching from operation level to initial setting level.

Note: 1.

Operation level entered for software reset.

2.

You cannot move to other levels by operating the keys on the front panel from the calibration level. You must turn OFF the power supply.

3.

The time taken to move to the protect level can be adjusted by changing the “Move to protect level time” setting. 

Troubleshooting

When an error has occurred, the No. 1 display shows the error code. Take necessary measure according to the error code, referring the table 
bellow.

Note: 1.

Refer to “E5CN-FR Limit Controller User’s Manual” for details of the control range.

2.

These errors are displayed only when the PV/Limit SP is displayed.

3.

If the display is restored to normal after cycling the power supply, the error may have been caused by noise. Check for noise being generated nearby.

No. 1 display

Meaning

Action

Status at error

Limit outputs

Alarm

s.err

Input error (See note 2.)
(broken line, A/D converter 
error)

Check the wiring of inputs, disconnections, shorts and input type. 
(See note 3.)

OFF

Operates as 
above the upper 
limit.

-lo-

Over lower-limit indication 
range (See note 2.)

Input value is smaller than control range.
Check the control range.

Upper limiter

Normal operation Operates as 

above the lower 
limit.

Lower limiter

OFF

-hi-

Over upper-limit indication 
range (See note 2.)

Input value is larger than control range.
Check the control range.

Upper limiter

OFF

Operates as 
above the upper 
limit.

Lower limiter

Normal operation

e111

Memory error

Turn the power OFF then back ON again. If the display remains the 
same, the controller must be repaired. (See note 3.)

OFF

OFF

[[[[

Over display range (lower-
limit display range) 
(See note 2.)

This is not an error. This is displayed when the input value exceeds 
the display limit but is within the control range.

Normal operation

Normal operation

Input password.

Input password. 

Set value 1201

Control in progress

Control stopped

Not displayed for some models

Level change

Power ON

Press the  
Level Key  
less than 1 s. 

Press the Level  
Key for at least 1 s.

Press the  
Level + Mode  
Keys. 
for at least 1 s

Press the  
Level + Mode Keys;  
display will flash.

(See  
note 1.)

(See  
note 2.)

Set value 

169

Press the 

Level Key for 

at least 1 s.

Press the Level Key 

for at least 1 s; 

display will flash.

Press the Level 
Key for at least 
3 s.

Press the Level + 
Mode Keys for at least 
3 s. (See note 3.)

Press the Level Key 
for less than 1 s.

l.adj

F

25

100

F

Operation Level

Adjustment Level

Control stops.

Protect Level

Initial Setting Level

Communications  
Setting Level

Advanced Function  
Setting Level

Calibration Level

Содержание E5CN-FR





















Отзывы: