![background image](http://html.mh-extra.com/html/omron/c200hw-clk21/c200hw-clk21_operation-manual_742483257.webp)
232
Response Codes
Section 6-7
05: Routing error
01
Destination node address is not set in
the routing table.
Set the destination node address in the
routing table.
02
Routing table isn’t registered.
Set the source nodes, destination nodes,
and relay nodes in the routing table.
03
Routing table error
Set the routing table correctly.
04
The maximum number of relay nodes
was exceeded in the command.
Redesign the network or reconsider the
routing table to reduce the number of relay
nodes in the command. Use a CS/CJ-series
CPU Unit with unit Ver. 2.0 or later with CX-
Programmer Ver. 4.0 or later to send com-
mands across three or more network levels.
10: Command format
error
01
The command is longer than the max.
permissible length.
Check the command format of the com-
mand and set it correctly.
02
The command is shorter than min. per-
missible length.
Check the command format of the com-
mand and set it correctly.
03
The designated number of data items
differs from the actual number.
Check the number of items and the data,
and make sure that they agree.
04
An incorrect command format has
been used.
Check the command format of the com-
mand and set it correctly.
05
An incorrect header has been used.
(The local node’s relay table or relay
node’s local network table is wrong.)
Set the routing table correctly.
11: Parameter error
01
A correct memory area code has not
been used or Extended DM Area is not
available.
Check the command’s memory area code
and set the appropriate code.
02
The access size specified in the com-
mand is wrong, or the first address is
an odd number.
Set the correct access size for the com-
mand.
03
The first address is in an inaccessible
area.
Set a first address that is in an accessible
area.
04
The end of specified word range
exceeds the acceptable range.
Check the acceptable limits of the data area
and set the word range within the limits.
Check the data link tables to be sure the
limit to link words has not been exceeded.
06
A non-existent program no. has been
specified.
Check the program number and be sure
that it is set correctly.
09
The sizes of data items in the com-
mand block are wrong.
Check the command data and be sure that
the sixes of the data items are correct.
Check the data link tables to be sure all
nodes in the refresh parameters are in the
common link parameters.
0A
The IOM break function cannot be exe-
cuted because it is already being exe-
cuted.
Either abort the current IOM break function
processing, or wait until it is completed and
execute the command.
Check the data link tables for node
addresses that have been set twice.
0B
The response block is longer than the
max. permissible length.
Check the command format and set the
number of items correctly.
0C
An incorrect parameter code has been
specified.
Check the command data and reenter it cor-
rectly.
Check the data link table file for corruption.
Main code
Sub-
code
Probable cause
Remedy
Содержание C200HW-CLK21
