manualshive.com logo in svg

OMP 60" Sbach 342, Руководство пользователя

Поделиться
Скачать
OMP 60

fuselage openings and connect to the proper aileron channels.  Servo clips are recommended.  Once you 
have the wings fully seated in the fuselage tighten the wing bolts inside the fuselage.    

3.  Position the canopy in place and check it is tight.    

4.  Check all control surfaces for secure hinges by performing a slight tug on the control surfaces and 
observing if there is any give in the hinges.  Check all control rods, ball links, servo screws, etc. for 
proper operation and installation.   

5.  Check your batteries and perform a proper range check once again with the engine off and running.  Be 
sure all surfaces are moving in the correct direction and the proper amount for your flying setup. 

6.  You are now ready for your maiden flight!  Good luck and enjoy your new aircraft!  If you have any 
comments or questions about this manual or the aircraft please email “

[email protected]

”. 

 

 

 

 

  

OHIO MODEL PRODUCTS 

199 Stratford Lane 

Xenia, Ohio 45385 

(937) 372-0603 

www.ohiomodelplanes.com

 

Содержание 60" Sbach 342

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды