background image

 

OPS-UM-001-C User Manual 

OmniPreSense Corporation 

11 

 

FCC 15B Statement

 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television reception, which can 
be  determined  by  turning  the  equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct  the 
interference by one or more of the following measures:  

Reorient or relocate the receiving antenna.  

Increase the separation between the equipment and receiver.  

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  

Consult the dealer or an experienced radio/TV technician for help. 

 

FCC 15C Statement

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) this device may not cause interference, and (2) this device must  accept any interference, including 
interference that may cause undesired operation of the device. 

 

FCC RF Exposure Statement 

This transmitter must be installed to provide a separation distance of at least 20cm from all persons and 
must not be co-located or operating in conjunction with any other antenna or transmitter. End-users must 
be provided with transmitter operation conditions for satisfying RF exposure compliance. 

  

IC Statement (English and French):

 

This  device  complies  with  ISED  Canada  license-exempt  RSS  standard(s).  Operation  is  subject  to  the 
following two conditions: (1) this device may not cause interference, and (2) this device must accept any 
interference, including interference that may cause undesired operation of the device. 

  

Le  présent  appareil  est  conforme  aux  CNR  d'ISED  Canada  applicables  aux  appareils  radio  exempts  de 
licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de 
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio électrique subi, même si le 
brouillage est susceptible d'en comprom-ettre le fonctionnement. 

Содержание OPS242














Отзывы: