Omnia ONE FM Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 70

Omnia ONE FM Скачать руководство пользователя страница 51

Appendix A: Performance Specifications

OmniaONE FM

As of July 2007 – Version 1.0 FM Software

Note: Discrete I/O measurements have been made in "Bypass" mode (available in the
Input/Output menu). FM composite measurements have been made using the "Proof_Perf"
preset.

General Audio Specifications

Frequency Response:

Complies with the standard 50 or 75 microsecond pre-emphasis curve

within ± 0.50 dB, 30 Hz to 15 kHz. The analog left/right outputs and

AES/EBU Digital outputs can be configured for flat or pre-emphasized

output.

System Distortion:

Less than 0.01% THD, 20 Hz – 7.5 kHz. Second harmonic distortion

above 7.5 kHz is not audible in the FM system.

*Signal-Noise Ratio:

> -80 dB de-emphasized, 20 Hz –- 15 kHz bandwidth, referenced to

100%

modulation).

*The measured noise floor will depend upon the settings of the Input and Output Gain controls and is primarily governed
by dynamic range of the Crystal Semiconductor CS5361 A/D Converter which is specified as >110 dB. The dynamic range
of the internal digital signal processing chain is >144 dB.

Stereo Separation:

Greater than 65 dB, 20 Hz –- 15 kHz; 70 dB typical..

Crosstalk:

> -70 dB, 20 Hz -- 15 kHz.

Composite Outputs:

Source Impedance: 5 ohms or 75 ohms, jumper-selectable. Single-ended

and floating over chassis ground.

Output Level: 0V to 10V in 0.05V steps, software adjustable.
D/A Conversion: Texas Instruments/Burr Brown PCM1798, 24-bit sigma-
delta converter.
Configuration: Two electrically independent outputs. Software based

level

adjustment.

Load Impedance: 50 ohms or greater load is suggested.

Pilot

Level:

Adjustable

from

4.0% to 12.0% in 0.1% steps and OFF.

Pilot Stability: 19 kHz, ± 0.5 Hz.

Signal-to-Noise Ratio: -85 dB typical, 75

μ

S de-emphasized, 15 kHz

bandwidth, referenced to 100% modulation).

Distortion:

<

0.02%

THD

20 Hz – 15 kHz bandwidth, 75

μ

S de-

emphasized,

referenced

to

100%

modulation.

Stereo Separation: > 65 dB, 30 Hz – 15 kHz.

39

«
...
49
50
51
52
53
...
»

Содержание ONE FM







































































Отзывы:

Нет отзывов