background image

   Document number 900-32003   Rev. A

8

System Power

   

CAUTION: NEVER HOOK UP OR DISCONNECT ANY EQUIPMENT WITH POWER
TURNED ON!

   The Inspection System requires a steady supply of 120VAC to operate properly.
Before starting of the generator or connecting shore power, make sure that ALL
equipment inside the vehicle has been turned 

OFF.

 Turn down the controls for camera

power and cable reel speed. After all equipment has been checked, connect the shore
power cord.

If a generator is to be used, allow the generator to warm up for a few minutes.

Note: Diesel generators use a different control panel that is separate from the
controller power supply. Refer to the appropriate generator operators manual for
starting.
Verify that the voltage and frequency indicators on the controller power supply are in
the green normal zone.

Caution: Before turning on any equipment, plug the keyboard into the data

collection system. Plug the Auxiliary Control Box into the Auxiliary

Control jack on the controller power supply.

Caution: If the voltage or frequency fluctuates into the red zones on the
controller power supply, DO NOT turn on any of the equipment in the truck.
Check shore power or the generator for proper operation, or have them checked
by a qualified technician.

Caution: Route cords away from traffic or wet areas to avoid tripping on

power cords.

Содержание 10-01610











Отзывы: