background image

2  

 

This manual is a guide for the use of the Omni Mixer and Omni Macro 

Homogenizers and accessories.  

 
Data herein has been verified and validated. It is believed adequate for the 

intended use of the instrument. If the instrument or procedures are used for 

purposes over and above the capabilities specified herein, confirmation of the 
validity and suitability should be obtained, otherwise Omni International does 

not guarantee results and assumes no obligation or liability. This publication is 

not a license to operate under, or a recommendation to infringe upon, any  

process patents.  
 

Notes, cautions, and warnings within the text of this manual are used to  

emphasize important and critical instructions. 

 
This Omni International product is warranted to be free from defects in  

material and workmanship for a period of THREE YEARS from the date of 

delivery. Omni International will repair or replace and return free of charge 
any part which is returned to its factory within said period, transportation 

prepaid by user, and which is found upon inspection to have been defective in 

materials or workmanship. For the first 90 days, both parts and service are 

without charge. For the balance of the period, parts will be provided but  
service will be charged at established labor rates. This warranty does not  

include normal wear from use;  it does not apply to any instrument or parts 

which have been altered by anyone other than an employee of Omni  
International nor to any instrument which has been damaged through  

accident, negligence, failure to follow operating instructions, the use of  

electric currents or circuits other than those specified on the plate affixed to 

the instrument, misuse, or abuse. Omni International reserves the right to 
change, alter, modify, or improve any of its instruments without any obligation 

whatever to make corresponding changes to any instrument previously sold 

or shipped. 

 
THE FORGOING OBLIGATION IS IN LIEU OF ALL OBLIGATIONS AND 

LIABILITIES INCLUDING NEGLIGENCE AND ALL WARRANTIES OF  

MERCHANTABILITY OR OTHERWISE, EXPRESSED OR IMPLIED IN FACT 
OR BY LAW, AND STATE OUR ENTIRE AND EXCLUSIVE LIABILITY AND 

BUYERS EXCLUSIVE REMEDY FOR ANY CLAIM OF DAMAGES IN  

CONNECTION WITH THE SALE OR FURNISHING OF GOODS OR 

PARTS, THEIR DESIGN, SUITABILITY FOR USE, INSTALLATION, OR  
OPERATION. OMNI INTERNATIONAL WILL IN NO EVENT BE LIABLE 

FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES WHATSOEVER, 

AND THEIR LIABILITY UNDER NO CIRCUMSTANCES WILL EXCEED 
THE CONTRACT PRICE FOR THE GOODS FOR WHICH LIABILITY IS 

CLAIMED. 

 

WARRANTY INFORMATION

 

Содержание Omni Mixer

























Отзывы: