Page - 8
Page - 13
The User Programmable Features
- SEE THE PREVIOUS SECTION FOR PROGRAMMING
INSTRUCTIONS -
Each of the Programmable Features is described in detail in the
following pages. The User Programmable Features are described as a
first group, and the Installer Programmable Features as a second group.
This group of User Programmable Features are all accessed as a group in the first
level of features’ programming. These features have a direct affect upon the
system’s operations, so the programming and operation of each are described.
The Excalibur RS-310’s 6
User Programmable Features
:
1
Remote Start Run Time
2
Steady / Flashing Lights During Remote Start
3
Confirmation Chirps / Volume
4
Pulsed Horn / Steady Siren
5
Doors Lock With Ignition On
6
Doors Unlock With Ignition Off
Use the step-by-step instructions on page 12, and the complete features matrix
on page 19, to change any of the programmable features. Each feature, the option
choices and related programming controller/transmitter button assignment are
described in detail in the following pages.
Step 7
Allow 10 seconds to pass without performing any programming
actions, or turn the vehicle’s ignition on.
• The horn will sound briefly (and the Status Indicator Light will go out).
To Access and Change further Features:
Step 6
If there are more features to be programmed, within 10 seconds of
the previous action Press & Release the Valet Switch the same
number of times as the next desired feature’s number.
• Again the horn will chirp, the parking lights, (and the Status Indicator Light)
will flash as many times as the Valet Switch was pressed to indicate the new
feature number which is now accessed. Then use the controller or transmitter
as described in
Step 5
to change the newly accessed feature as desired.
•
With the system in a locked state, simply turn the ignition key to the
RUN/ON position.
•
Press and release the valet switch once.
You should now be able to access programming functions.
Pit-Stop Feature
This feature allows you to turn off the ignition switch, remove your keys,
leave the vehicle and lock your doors while leaving the engine running. To
use this feature, have the engine running normally from the ignition switch,
have the gear selector in “park”, and your foot off of the brake pedal. Press
the Valet Switch twice; the parking lights will flash once and the horn chirps
5 times; then turn the ignition off. The engine will remain running for the
programmed run time, or it will turn off if another transmitter signal is re-
ceived, a safety circuit is violated, or if the Valet Switch is pressed.
This feature may be used anytime; it does not have to be specially
programmed to operate.
Turbo Timer Feature
It is typically recommended that vehicles equipped with turbocharged
engines allow the engine to idle for a few minutes before turning it off.
When this Installer Programmable Feature is programmed on, the RS-310
will automatically keep the engine running as follows:
•
With the engine running, hold the brake pedal and engage the parking
brake. When the brake pedal is released, the RS-310 will keep the
engine running for the selected time, and then automatically turn it off.
Low Battery Automatic Starting Feature
This feature may be used anytime. Setting this feature to operate has
the RS-310 automatically start the engine should the vehicle battery volt-
age drop to 10.5 volts. This feature is very useful if the vehicle is to parked
unattended for a long period of time, such as extended parking at the air-
port while away. Low Battery automatic starting must be activated for each
occasion in which you desire it to operate, as follows:
•
Turn the ignition switch “on”, then “off” (engine not running), and within
7 seconds press the brake pedal twice. The system will chirp 6 times.
Then, within 5 seconds, exit the vehicle and press the transmitter’s
“lock” button to lock the vehicle.
The feature is now turned on, and until the system is disarmed or the
ignition turned “on”, if the system detects the vehicle battery voltage drop-
ping to 10.5 volts, it will automatically start the engine.
Other Remote Start Features
