manualshive.com logo in svg
background image

3

4.0   HHT13 SPECIFICATIONS

Laser Specifications:

Classification:

Class 2 (per IEC 60825-1 Ed 1.2 2001-8)

Complies with FDA performance standards for laser products except
for deviations pursuant to Laser Notice No. 50, dated July 26, 2001.

Maximum Laser Output:

1mW

Pulse Duration:

Continuous

Laser Wavelength:

650 nm

Beam Divergence:

< 1.5 mrad

Beam Diameter:

4 x 7 mm typical at 2 meters

Laser Diode Life:

8,000 operating hours MTBF (1 year

warranty)

Non-Contact Specifications:

Ranges:

RPM

5 – 200,000

RPS

0.084 – 3,333.3

RPH

300-999,990

Resolution:

Fixed:

1 (10 above 99,999)

Auto-ranging: 0.001 to 1.0 (10 above 99,999)

Accuracy:

±

0.01% of reading or resolution limit

Operating Range:

up to 25 feet (7.62 m) or up to 70 degrees off
perpendicular to reflective tape target

Contact Specifications using optional Remote Contact Assembly:

Range:

Contact Tips:

0.5 to 20,000 RPM

10 cm / 12-inch Wheel: 0.5  to  12,000  RPM

Resolution:

Fixed:

1 (10 above 99,999)

Auto-ranging:

0.001 to 1.0 (10 above 99,999)

20

8.

Save and
advance

9.

Exit Setup –
Ready to
measure

Measure:

Reset

Lap

Power Off

Unit will remember these settings (including lock on/off) even if turned off
and back on.

DONE

, then Units

selected

Manual

Auto

Each press toggles Start and Stop

Start and Stop triggered by
Remote Optical Sensor
(HHT20-ROS)

With Timer stopped -
Resets time to 00:00.0

With Timer running -
Stops at elapsed time to date.
To continue, press again.

OR

9.2 TIMER Operation

Automatic after 90 seconds
if unit not Locked on

OR

Содержание HHT13















Отзывы: