Emergency Override:
In the event that your transmitter is lost, damaged, or its batteries have become
exhausted, the Valet Switch and the vehicle’s ignition key may be used to disarm
the system. These Emergency Override instructions reflect a default setting of “1
press”; please note that the “SecureCode” programmable feature, described on the
following page, allows the owner to customize the number of Valet Switch
presses needed for the Emergency Override.
DISARMING BY EMERGENCY OVERRIDE
Page 13
ENTER THE VEHICLE
AND USE YOUR KEY TO
TURN THE IGNITION ON
WITHIN 5
SECONDS OF
TURNING THE
IGNITION ON,
PRESS AND RELEASE
THE VALET SWITCH
THE SYSTEM WILL DISARM
To Disarm the System without using a Transmitter:
Step 1 With the system in the armed condition, enter the vehicle via the driver's
door (be aware that the system will activate to an alarm condition when
the door is opened).
Step 2 Using the ignition key, turn the vehicle’s ignition on.
Step 3 Within 5 seconds, press and release the Valet Switch once. The system
will immediately disarm.
matic Rearming period. For example, if a vehicle door is opened during the
90 second period, the countdown will stop. When the door is closed, the
system resets and starts a new 90 second countdown period.
• The Automatic Rearming sequence is indicated by a fast flashing Red Status
Indicator Light, unless the system has been activated, in which case a Zone
Violation Code will flash instead (pages 23-24). The ignition switch must be
turned on to erase a violation code.
• If the system is disarmed while it is activated (siren sounding and lights
flashing) Safety Disarm will cancel the Automatic Rearming for that disarming
operation only. The next time the system is armed, Automatic Rearming will
be initiated upon the subsequent disarming.
Page 36
Feature #20
Remote Start Preactivation
(Factory Default Off)
This feature requires that the user press the Valet Switch once before exiting
the vehicle in order for the remote starting operation to be available for later use.
With Preactivation is turned off, remote starting can be performed at any time,
and repeatedly if desired. If this feature is turned on, the system will not attempt
to start the engine unless the Valet Switch was pressed some time prior to the
starting attempt, as when leaving the vehicle.
Programming Preactivation:
Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and
released twenty times. The system’s response will be twenty siren chirps, and the
Status Light flashing twenty times, pausing, then repeating. Within 10 seconds,
press and release the transmitter/transceiver’s "Arm/Lock" button to configure
the system Preactivation operable (the siren will chirp once) or the "Disarm/
Unlock" button to configure the system to turn off the Preactivation operation
(the siren will chirp twice).
Feature #21
Steady Siren or Pulsed Horn Output
(Factory Default Setting Steady Siren)
This feature allows the choice using of the vehicle's horn for the audible
output of the security system instead of the electronic siren. When programmed
configure the system for 20 minute remote start engine run time (the siren will
chirp once) or the "Disarm/Unlock" button to configure the system for 10 minute
run time (the siren will chirp twice).
Feature #19 Steady/Flashing Lights During Remote Start
(Factory Default Setting Steady)
This Feature configures the system's operation of the vehicle’s parking lights
when the engine is running after it has been remotely started. The factory default
setting has the parking lights illuminating steady during the engine run time; the
other option flashes the parking lights on and off during the engine run time.
Programming Steady or Flashing Parking Lights:
Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and
released nineteen times. The system’s response will be nineteen siren chirps, and
the Status Light flashing nineteen times, pausing, then repeating. Within 10
seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to
configure the system for steady parking lights (the siren will chirp once) or the
"Disarm/Unlock" button to configure the system for flashing parking lights (the
siren will chirp twice).
