background image

6

Installation

MAIN CHARACTERISTICS OF THE TOOLS WHICH CAN BE INSTALLED IN THE 

MACHINE

The machine is supplied with a plate - each hole of which has a diameter of 6/8 mm. To perform different 

processing operations, however, it is possible to fit in plates with holes having a smaller diameter compared 

with the plate supplied by the manufacturing company without modifying the functional characteristics of the 

machine.

SETTING UP THE MACHINE

• 

Fit the body into its seat in the motor assembly after partially unscrewing the hand wheel. Make sure that 

the body has been fitted with the meat-supply opening turned up and that it has been driven into its seat 

up to the end; lock into place by turning the hand wheel to the end without forcing the locking position too 

much.

• 

If the body has been properly assembled, it cannot be taken out or revolve in its seat.

• 

Fit horizontally the screw in the body on the side of the grooved shaft driving it on the bush (a component 

placed inside the body).

• 

At this stage, if necessary, slightly rotate the screw so that the insertion of the clutch into the motor drive 

will be made easier.

•  Fit in sequence in the pin with the square dragging part jutting out from the screw: the grinding blade with 

the cutting edge facing outside, and the perforated plate with the fat side facing the cutting edge of the 

blade. When fitting in the blade, make sure that the square dragging part is properly inserted.

• 

Check if the outside notch in the plate is positioned in connection with the special fastening tooth placed on 

the body so that the plate cannot revolve once it has been fitted in the body.

• 

Lock into position by screwing the threaded crown on the corresponding thread in the body; do not force 

the locking position with any tool. Locking effected manually is enough.

• 

After making sure that the motor switch is at 0, you can plug in.

• 

The machine is now ready to work and you can start it by putting the motor switch/reversing switch to 

Model

MG-IT-0032

Power

1.5 HP / 1.1 kW

Motor Size

1100 Watts

RPM

110

Throat Opening

2” approx.

Electrical

110 V / 60 Hz / 1 Ph

Weight

77 lbs. / 34.9 kg.

Dimension (DWH)

22.4” x 11” x 17” / 570 x 279 x 432mm

Item Number

11013

Technical Specifications

Содержание MG-IT-0032

















Отзывы: