![background image](http://html2.mh-extra.com/html/omcan/fp-it-0006/fp-it-0006_instruction-manual_5153230012.webp)
12
Operation
MACHINE STOP
To stop the machine, press button “2” (stops the electric motor). Then, switch the circuit breaker installed
upstream of the machine to “0”, thereby disconnecting the cutter.
USE OF THE MACHINE
PERSONS AUTHORISED TO OPERATE THE MACHINE
IMPORTANT!
Only authorised staff can intervene on the machine. Before using the machine, the operator must ensure that
all guards are in place and that the safety devices are installed and efficient. Otherwise, turn the machine off
and contact the person in charge of maintenance. Make sure there is sufficient lighting to allow proper visibility
to the operator. Run the machine idle a couple of times with the assistance of qualified personnel, in order to
familiarise with the machine enough to operate it safely.
OPERATING MODE OF THE CUTTER
To load products onto the cutter, the circuit breaker must be switched to “0” (off). The product to be minced
must fit in the tank and must not exceed the maximum weight indicated in this manual. Close the lid (locking it
by turning the knob counterclockwise) and start the machine.
EMPTYING AND CLEANING THE TANK
EMPTYING THE TANK
Turn off the machine, set the circuit breaker to “0” and detach the power plug.
• Rotate the lid release knob “1” counter-clockwise (Fig. 6.3.1).
• Raise the lid “2” (Fig. 6.3.2).
• Turn the lock knob of the blade holder “3” (Fig. 6.3.2).
• Remove the blade holder “4” (Fig. 6.3.2) from the shaft
• Turn the tank “5” counter-clockwise (Fig. 6.3.3) in order to release it from its seat.
•
Lift and remove the tank.
•
Proceed to empty out the tank by removing the shredded product.
CLEANING THE TANK
With the machine off, the circuit breaker set to “0” and the power plug detached, clean the tank.
• Rotate the lid release knob “1” counter-clockwise (Fig. 6.3.1).
• Raise the lid “2” (Fig. 6.3.2) and extract it from its seat.
• Turn the lock knob of the blade holder “3” (Fig. 6.3.3).
• Remove the blade holder from the shaft “4” (Fig. 6.3.3).
• Turn the tank “5” counter-clockwise (Fig. 6.3.4) in order to release it from its seat.
•
Lift and remove the tank.
• The surface is now smooth and easy to clean. (Fig. 6.3.4).
•
Proceed to thoroughly clean the machine and disinfect it if necessary.
• With a sponge soaked in water and neutral (pH 7) and non-toxic degreasing products, remove all
processing residue from the machine and blades.
Do not use gasoline, solvents or other flammable liquids as detergents; instead, use authorised commercial
Содержание FP-IT-0006
