ROERO - TST
________________________________________________________________________________
19
Greasing- Lubrification
Overgear unit
oil type SPARTAN 220
quantity: 1.50 litres
check the level every 50 hours with the special rod A
replace the oil after the first 150 hours using screw B
Rotor bearings, supports
All the machine bearings are pre lubricated for life and no greasing is necessary
Automatic turnbuckle
to be greased every 8 working hours
Roller bearing
this bearings are to be greased every 8 working hours
PTO shaft joint
Grease the following evertu 8 working hours:
the cross journal A
the tubes B
the sliding spacer elements C
oil the masks D every 120 working hours
Automatic belt turnbuckle
If necessary the spring tension must be insreased by means of lever A (Fig.19)
Check the spring tension:
after the first ½ hour of work
after the first 8 working hours
every 20 working hours
Cutters
Check daily that thereare no broken cutters.
If there are, replace it with the one diametrically opposite, in order to maintain a correct tractor balance.
Do not wait until the cutters are excessively worn before replacing, as it causes:
morepower to be used
vibrations thatare detrimental to the rotating parts of the shredder
ROERO - TST
________________________________________________________________________________
20
Counter-cutter
Regularly check its condition and clean, especially when the vegetation is damp.
Storage
Before storing the machine:
wash it thoroughly
check the parts subject to wear (cutters, belts)
spray a fine film of oil or diesel over the entire machine to protect it against rust
Going into the road
1.
before beginning work check all the nuts and bolts and then again after the first 50 working hours
2.
correctly connect the machine to the tyractor
3.
check that the PTO running speed is at 540 or 1000 rpm
4.
insert the PTO with a slow running speed, with the wheels resting on the ground and the machine horizontal
5.
go freward by a few metres and check the cutting height. adjust if necessary
Warning!
All the greasing, lubrication, maintenance, repair, parts substitution, setting onto the road operations must be carried out slowly
with the greatest care in compliance with the safetu regulations of this manual. failire to respect event one of these regulations
may cause seroius injury or death to the operator or the accompanying personnel.
Warranty
The company OMARV SRL warrants for 12 months from the date of delivery of new machine of his own making.
The warranty does not cover PTO shaft, blades, bearings and belts. These parts are warranted by the respective manufacturer.
During the months of warranty OMARV SRL is committed to provide free part found defective by its technical department but are
charged to the customer all freight, packaging and labour. Changes made by the client on the machine, use different from that stated in
the manual for use and handling, carelessness of the user and the use of parts not manufactured, voids the warranty.
OMARV SRL disclaims all liability for damages suffered by the client because of the breakdown of the machine or its part, delayed
delivery, as well as because of the use of the machine itself. For technical and administrative reasons, all parts will be charged at time of
shipment. The acceptance of any warranty claim and the right credit will take place upon receipt and verification of the defective part.
For all the controversy jurisdiction is one of Asti, Italy.
Содержание ROERO TST 120
