OmarLift HI Скачать руководство пользователя страница 3

Страница: 3 / 32

D860MGB rev04

TEST AND WORKING OF THE RUPTURE VALVE ....................................................................... 18

VALVE GROUP AND INVERTER’S PARAMETER CALIBRATION AND ADJUSTMENT ..................... 18

GENERAL INFORMATION ............................................................................................................. 18

8.2

HYDRAULIC SCHEME .................................................................................................................... 19

8.3

ADJUSTING AND REGULATION OF “HI” VALVE GROUP ........................................................... 20

OVER-PRESSURE VALVE CALIBRATION: SCREW N°1 ..................................................... 20

ROD COUNTER-PRESSURE AND ROPE ANTI-LOOSENING CALIBRATION: SCREW N. 3

CALIBRATION OF THE HAND PUMP PRESSURE: SCREW N. 9 ........................................ 21

CALIBRATION OF THE PRESSURE SWITCHES (PRESSURE MIN. - MAX. - OVERLOAD)

8.4

INVERTER SETTING AND PROGRAMMING ................................................................................ 23

OPTIONAL ACCESSORIES ................................................................................................................... 23

9.1

OIL HEATING RESISTANCE (optional) .......................................................................................... 23

9.2

OIL COOLING (optional) ................................................................................................................. 23

GENERAL INFORMATION ..................................................................................................... 23

COOLING SYSTEM WITH AIR ............................................................................................... 24

COOLING SYSTEM WITH WATER ........................................................................................ 24

MAINTENANCE ................................................................................................................................... 25

10.1

GENERAL INFORMATION ............................................................................................................. 25

10.2

OIL LOSSES AND CAR LOWERING .............................................................................................. 25

LOSSES ALONG THE PIPES ................................................................................................. 25

CYLINDER LOSSES ............................................................................................................... 25

LOSSES INSIDE THE VALVE GROUP .................................................................................. 25

10.3

AIR PRESENCE IN THE OIL .......................................................................................................... 29

10.4

FILTER CLEANING INSIDE VALVE GROUP ................................................................................. 29

10.5

MINERAL OIL DETERIORATION ................................................................................................... 29

10.6

ELECTRICAL ANTI-CREEP SYSTEM (RE-LEVELING) ................................................................ 30

10.7

EMERGENCY LOWERING WITH THE BATTERY ......................................................................... 30

10.8

PLATES, DIAGRAMS, INSTRUCTIONS ......................................................................................... 30

10.9

INVERTER MAINTENACE .............................................................................................................. 30

MEGGER TEST ....................................................................................................................... 30

10.10

RECOMMENDED PERIODIC MAINTENANCE .............................................................................. 30

DIMENSIONS AND WEIGHTS............................................................................................................ 31

11.1

DIMENSIONS AND WEIGHTS OF THE PUMP UNITS .................................................................. 31

11.2

DIMENSIONS AND WEIGHTS OF INVERTER AND RESISTORS ................................................ 31

Содержание HI

































Результаты поиска

Содержание HI

Отзывы:

OmarLift HI, Руководство по эксплуатации, Страница: 3 / 32

Результаты поиска

Содержание HI

Отзывы: