OmarLift HI Скачать руководство пользователя страница 31

Страница: 31 / 32

D860MGB rev04

31/32

PRESERVATION
CLEANING OF THE SHUT-OFF VALVE AND
VALVE FILTERS

10.4

CHECK OF THE PRESSURE AND ADJUSTING
AT TWICE THE MAX STATIC PRESSURE

6.2
6.6

CHECK OF THE RUPTURE VALVE WORKING

7.2

CHECK OF THE ROPE ANTI-LOOSENING
COUNTER-PRESSURE

6.7

CHECK OF THE ELECTRICAL ANTI-CREEP
SYSTEM

10.6

CHECK OF THE EMERGENCY AND BATTERY

10.7

PLATES

– DIAGRAMS – INSTRUCTIONS

10.8

GENERAL OVERHAUL

XXXX

CLEANING OF THE INVERTER FAN

10.9

CHECK OF THE ELECTRICAL INVERTER
CONNECTION

10.9

11 DIMENSIONS AND WEIGHTS

11.1

DIMENSIONS AND WEIGHTS OF THE PUMP UNITS

The weights of the pump units with shut-off valve are divided per kind of tank and do not consider the weight
differences of pumps and motors of different size. Consequently there is a are approx. calculated with a 5%
tolerance.

TANK TYPE

TANK BASE (HANDLES
INCLUDED) MM

HEIGHT

(TANK

VALVE) MM

PUMP UNIT WEIGHT
(OIL EXCLUDED) KG

110

774 x 300

702 + 260

105

135

774 x 300

702 + 260

110

210

904 x 400

810 + 260

145

320

1024 x 460

950 + 260

176

450

1074 x 700

952+ 270

230

11.2

DIMENSIONS AND WEIGHTS OF INVERTER AND RESISTORS

Refer to the manual of the inverter.

Содержание HI

































Результаты поиска

Содержание HI

Отзывы:

OmarLift HI, Руководство по эксплуатации, Страница: 31 / 32

Результаты поиска

Содержание HI

Отзывы: