background image

E-34

8. Appendix

Q & A on the use of the PT-032

Q1 : What digital camera models can be used with this product?
A1 : This product (PT-032) is designed exclusively for use with the Stylus

710/700 and µ710/700 digital cameras.

Q2 : What cautions must be observed when loading the digital camera

into the Case?

A2 : Pay special attention to the following items when loading the camera

into the Case.

(1) Make sure that the  digital camera has enough battery power left.

Battery power is used up very quickly underwater due to frequent
flash use.

(2) Check the remaining number of pictures on the image storage.

Please use a card with a sufficient remaining number in order to
reduce the number of times the Case has to be opened and closed.

(3) Remove the strap from the digital camera.

When the camera is loaded without removing the strap, the strap may get
caught when the Case is sealed and this will cause water leakage.

(4) Turn the camera OFF and set both the camera’s mode dial and the

mode dial on the rear lid of the Case to “SCENE.”

(5) Before sealing the Case, confirm that the O-ring has been installed

properly in the groove in the rear lid of the Case.

(6) Confirm that the O-ring and the O-ring contact surface on the front lid

are free of dirt, hairs, and other foreign matter.

(7) Insert the silica gel for defogging. Please use silica gel for the

Olympus Case.

Q3 : What cautions must be observed when using and storing the Case?
A3 : Pay special attention to the following items.

(1) When the O-ring contact surface is pressed strongly from the outside

of the Case, or when the Case is twisted, the waterproof function may
be impaired and water leakage may be caused.

(2) When the Case is used, left or stored at the following locations,

defective operation or trouble may be caused. Always avoid such
locations.
(a) Places where the Case can reach high temperatures under direct

sunlight or in a car, places with extremely low temperatures, and
places with extreme temperature variations

(b) Places with open fire

PT032̲E.qxd  05.12.27  7:34 PM  ページE-34

Содержание PT-032













































Отзывы: