background image

E-20

Perform the final checks.

Visual Inspection

After sealing the Case, check the sealing part of front and rear lid
visually to confirm that the O-ring is not twisted or out of the groove
and that no foreign matter has been caught.

Fit the lens cap onto the lens
ring as shown in the figure. Be
sure to remove the lens cap
before shooting.

Mounting and Removing the Lens Cap

:

• After loading the camera into the Case, confirm that the

mode dial moves. If it does not move, there is the possibility
that oil or fat has been attached to the mode dial. Please
wipe it clean.

• When no operation is performed for three minutes after the

digital camera has been loaded (or for the specified time
when a different time has been specified), the camera
enters into sleep mode (standby status) to save battery
power. It returns to operation status when the shutter button
or the zoom lever is operated.
For details, refer to the instruction manual for the digital
camera.

CAUTION

Try to move the mode dial.

After sealing, turn the mode dial knob and confirm that the mode
dial of the camera is switched.

Set the power to 'ON'.

Move the power switch lever and confirm that the camera power
can be switched ON and OFF.

:

• Hairs, fibers, and other narrow items are not very apparent,

but they may cause entry of water, so that special attention
is required.

CAUTION

PT̲019̲en.qxd    2003.9.19  2:13  PM    ページ E-20 (1,1)

Содержание PT-019







































Отзывы: