Olympus OmniScan MX2 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 228

Olympus OmniScan MX2 Скачать руководство пользователя страница 93

DMTA-20015-01EN [U8778402], Rev. J, January 2014

Overview of the Equipment

81

7.1.9.3

Acquisition Indicator Light

The acquisition indicator light is located to the left of the Start/Stop key (

). The

color of this light indicates the OmniScan MX operating mode (see Table 19 on
page 81).

If an acquisition module is removed while the OmniScan MX is turned on, the
keypad, power, and acquisition indicator lights flash red for a few seconds, and then
the unit automatically shuts down to prevent damage to the internal circuits.

Table 18 Power indicator light statuses

Off

The OmniScan MX is turned off.

Green

The instrument is ready (start-up
complete).

Orange

Battery charging is complete.

Flashing orange/green

The OmniScan MX is shut off. Battery A is
charging.

Flashing orange/red

The OmniScan MX is shut off. Battery B is
charging.

Flashing red

Critical factor (temperature, very weak
battery, etc.)

Table 19 Acquisition indicator light statuses

Off

Acquisition mode

Flashing orange

Paused analysis mode

«
...
91
92
93
94
95
...
»

Содержание OmniScan MX2





































































































































































































































Отзывы:

Нет отзывов