Olympus OmniScan MX Скачать руководство пользователя страница 105

Страница: 105 / 230

DMTA-20015-01EN [U8778402], Rev. M, February 2017

Basic Operation

8.2.4

Battery Removal and Installation

To remove and install a battery

Open the battery compartment door on the right side panel of the instrument by
pressing the two plastic buttons towards each other.

If there is already a battery in the compartment, pull the cloth tab to remove the
battery (see Figure 8-3 on page 94).

Table 19 Battery status indicator variations

Indicator

Outline

Fill

Meaning

Dotted

N/A

There is no battery in that compartment.

Blue

The battery is functioning properly.

Blue

Orange

The battery is too hot for use.

Yellow

(blinking)

Blue

The battery is charging.

Orange

Blue

The battery is too hot to be charged.

Red

(blinking)

Blue

The battery charge is critically low (less
than 10 %). A beeping noise sounds
when there is no spare battery available.

N/A

Yellow

The OmniScan MX is being powered
externally through the DC adaptor.

N/A

Dark

green

The external power supply is
insufficient.

Содержание OmniScan MX







































































































































































































































Результаты поиска

Содержание OmniScan MX

Отзывы:

Похожие инструкции для OmniScan MX

Бренды по названию

Популярные бренды

Olympus OmniScan MX, Руководство пользователя

Результаты поиска

Содержание OmniScan MX

Отзывы:

Похожие инструкции для OmniScan MX

Бренды по названию

Популярные бренды