Olympus OmniScan MX Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 230

background image

DMTA-20015-01EN [U8778402], Rev. M, February 2017

Basic Operation

37

You can also turn off the OmniScan MX2 by pressing and holding the Power key for
ten seconds. However, your setup will NOT be saved.

2.2

Automatic Start-Up Mode

The OmniScan MX2 has an automatic start-up mode: auto-boot. Use the auto-boot
mode to remotely start the OmniScan MX2 instrument. When this mode is enabled,

you do not need to press the Power key (

) to start the OmniScan MX2. The

OmniScan MX2 starts up automatically when connected to a DC power adaptor. This
mode is disabled by default.

To activate the auto-boot

1.

Turn off the OmniScan MX2 instrument, remove the batteries, and then
disconnect the DC power adaptor.

2.

Press and hold the Power key (

).

3.

Connect the OmniScan MX2 to a DC power adaptor.

4.

Wait for the power indicator light to blink two times, and then release the Power

key (

).

5.

To deactivate the auto-boot, repeat steps 1 to 4.

2.3

Power Supply Management

The OmniScan MX2 is a portable instrument that can draw power from either
lithium-ion batteries or a DC power adaptor.

NOTE

«
...
47
48
49
50
51
...
»

Содержание OmniScan MX







































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OmniScan MX

Бренд: Samson Страницы: 4

Бренд: 3nh Страницы: 10

Бренд: Facom Страницы: 42

HYGRASREG KH-30

Бренд: S+S Regeltechnik Страницы: 16

BLITZFIRE Series

Бренд: Task Force Tips Страницы: 20

Бренд: P3 International Страницы: 1

Бренд: Danfoss Страницы: 80

OPTIFLUX 4040 C Series

Бренд: KROHNE Страницы: 20

Бренд: Anritsu Страницы: 29

Бренд: VWR Страницы: 44

Бренд: Power Measurement Страницы: 20

Бренд: RADWAG Страницы: 176

Бренд: Young Страницы: 5

SiteHawk SK-6000

Бренд: BIRD Страницы: 69

Бренд: GAGEMAKER Страницы: 36

Бренд: Amrutha Technologies Страницы: 22

Бренд: Straightpoint Страницы: 24

Бренд: Hammerhead Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды