Olympus OmniScan MX Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 230

background image

DMTA-20015-01EN [U8778402], Rev. M, February 2017

Chapter 8

94

Figure 8-3 Removing the lithium-ion battery

3.

Insert a new battery. Make sure that the groove on the battery is aligned with the
small edge inside the battery compartment.

4.

Close the battery compartment door.

The batteries are recharged inside the OmniScan MX when it is connected to a DC
power adaptor. Connecting an adaptor automatically starts the recharging process.
The batteries can also be recharged using an optional external charger.

8.2.5

Battery Charging

To charge the OmniScan MX batteries



Connect the OmniScan MX to a proper DC power adaptor.
Battery charging is performed as follows:
— When the OmniScan MX is turned off:

When the OmniScan MX is connected to a proper DC power source and is
turned off, it will automatically recharge any battery with less than 85 %
remaining charge, starting with the weakest battery (if the recharge
conditions are met).

Lithium-ion
battery

Cloth tab

Battery
compartment
door

«
...
104
105
106
107
108
...
»

Содержание OmniScan MX







































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OmniScan MX

Бренд: Keithley Страницы: 48

Бренд: Lambrecht Страницы: 5

Бренд: Keithley Страницы: 25

Бренд: Hardy Barth Страницы: 27

Бренд: QMI Страницы: 54

Бренд: Parkside Страницы: 114

Бренд: G-Tek Страницы: 83

Бренд: Hanna Instruments Страницы: 2

Бренд: Gearx Страницы: 19

Бренд: BizLine Страницы: 62

Digital Piano CA440

Бренд: Kawai Страницы: 48

Бренд: Polimaster Страницы: 24

Бренд: Suaoki Страницы: 79

Бренд: National Instruments Страницы: 40

Бренд: Hioki Страницы: 16

Бренд: Digitimer Страницы: 58

Бренд: Voweek Страницы: 20

Бренд: Lasertec Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды